|
|
|
|
|
|
IETF RFC 8467
Padding Policies for Extension Mechanisms for DNS (EDNS(0))
Last modified on Saturday, October 13th, 2018
 Permanent link to RFC 8467
 Search GitHub Wiki for RFC 8467
 Show other RFCs mentioning RFC 8467
Internet Engineering Task Force (IETF) A. Mayrhofer
Request for Comments: 8467 nic.at GmbH
Category: Experimental October 2018
ISSN: 2070-1721
Padding Policies for Extension Mechanisms for DNS (EDNS(0))
 Abstract
RFC 7830 specifies the "Padding" option for Extension Mechanisms for
DNS (EDNS(0)) but does not specify the actual padding length for
specific applications. This memo lists the possible options
("padding policies"), discusses the implications of each option, and
provides a recommended (experimental) option.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for examination, experimental implementation, and
evaluation.
This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). It represents the consensus of the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents approved by the IESG are candidates for any level of
Internet Standard; see Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/RFC 8467.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Mayrhofer Experimental PAGE 1 
RFC 8467 Padding Policies for EDNS(0) October 2018
Table of Contents
1. Introduction ....................................................2
2. Terminology .....................................................2
3. General Guidance ................................................3
4. Padding Strategies ..............................................3
4.1. Recommended Strategy: Block-Length Padding .................3
4.2. Other Strategies ...........................................5
4.2.1. Maximal-Length Padding ..............................5
4.2.2. Random-Length Padding ...............................5
4.2.3. Random-Block-Length Padding .........................6
5. IANA Considerations .............................................6
6. Security Considerations .........................................6
7. References ......................................................7
7.1. Normative References .......................................7
7.2. Informative References .....................................7
Appendix A. Padding Policies That Are Not Sensible ................8
A.1. No Padding .................................................8
A.2. Fixed-Length Padding .......................................8
Acknowledgements ...................................................9
Author's Address ...................................................9
1. Introduction
[RFC 7830] specifies the Extension Mechanisms for DNS (EDNS(0))
"Padding" option, which allows DNS clients and servers to
artificially increase the size of a DNS message by a variable number
of bytes, hampering size-based correlation of encrypted DNS messages.
However, RFC 7830 deliberately does not specify the actual length of
padding to be used. This memo discusses options regarding the actual
size of padding, lists advantages and disadvantages of each of these
"padding strategies", and provides a recommended (experimental)
strategy.
Padding DNS messages is useful only when transport is encrypted using
protocols such as DNS over Transport Layer Security [RFC 7858], DNS
over Datagram Transport Layer Security [RFC 8094], or other encrypted
DNS transports specified in the future.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC 2119] [RFC 8174] when, and only when, they appear in all
capitals, as shown here.
Mayrhofer Experimental PAGE 2
RFC 8467 Padding Policies for EDNS(0) October 2018
3. General Guidance
EDNS(0) options space: The maximum message length, as dictated by the
protocol, limits the space for EDNS(0) options. Since padding will
reduce the message space available to other EDNS(0) options, the
"Padding" option MUST be the last EDNS(0) option applied before a DNS
message is sent.
Resource Conservation: Especially in situations where networking and
processing resources are scarce (e.g., battery-powered long-life
devices, low bandwidth, or high-cost links), the trade-off between
increased size of padded DNS messages and the corresponding gain in
confidentiality must be carefully considered.
Transport Protocol Independence: The message size used as input to
the various padding strategies MUST be calculated excluding the
potential extra 2-octet length field used in TCP transport.
Otherwise, the padded (observable) size of the DNS packets could
significantly change between different transport protocols and reveal
an indication of the original (unpadded) length. For example, given
a Block-Length Padding strategy with a block length of 32 octets and
a DNS message with a size of 59 octets, the message would be padded
to 64 octets when transported over UDP. If that same message were
transported over TCP and the padding strategy considered the extra 2
octets of the length field (61 octets in total), the padded message
would be 96 octets long (as the minimum length of the "Padding"
option is 4 octets).
4. Padding Strategies
This section contains a recommended strategy, as well as a
non-exhaustive list of other sensible strategies, for choosing
padding length. Note that, for completeness, Appendix A contains two
more strategies that are not sensible.
4.1. Recommended Strategy: Block-Length Padding
Based on empirical research performed by Daniel K. Gillmor
[NDSS-PADDING], padding SHOULD be performed following the Block-
Length Padding strategy as follows:
(1) Clients SHOULD pad queries to the closest multiple of 128
octets.
(2) If a server receives a query that includes the EDNS(0) "Padding"
option, it MUST pad the corresponding response (see Section 4 of
RFC 7830) and SHOULD pad the corresponding response to a
multiple of 468 octets (see below).
Mayrhofer Experimental PAGE 3
RFC 8467 Padding Policies for EDNS(0) October 2018
Note that the recommendation above only applies if the DNS transport
is encrypted (see Section 6 of RFC 7830).
In Block-Length Padding, a sender pads each message so that its
padded length is a multiple of a chosen block length. This creates a
greatly reduced variety of message lengths. An implementor needs to
consider that even the zero-length "Padding" option increases the
length of the packet by 4 octets.
Options: Block length. For queries, values between 16 and 128 octets
were discussed before empiric research was performed. Responses will
require larger block sizes (see [NDSS-PADDING] and above for a
discussion).
Very large block lengths will have confidentiality properties similar
to the Maximal-Length Padding strategy (Section 4.2.1), since almost
all messages will fit into a single block. Such "very large block
length" values are:
o 288 bytes for the query (the maximum size of a one-question query
over TCP, without any EDNS(0) options) and
o the EDNS(0) buffer size of the server for the responses.
Advantages: This policy is reasonably easy to implement, reduces the
variety of message ("fingerprint") sizes significantly, and does not
require a source of (pseudo) random numbers, since the padding length
required can be derived from the actual (unpadded) message.
Disadvantage: Given an unpadded message and the block size of the
padding (which is assumed to be public knowledge once a server is
reachable), the size range of a padded message can be predicted.
Therefore, the minimum length of the unpadded message can be
inferred.
The empirical research cited above performed a simulation of padding,
based on real-world DNS traffic captured on busy recursive resolvers
of a research network. The evaluation of the performance of
individual padding policies was based on a "cost to attacker" and
"cost to defender" function, where the "cost to attacker" was defined
as the percentage of query/response pairs falling into the same size
bucket and "cost to defender" was defined as the size factor between
padded and unpadded messages. Padding with a block size of 128 bytes
on the query side and 468 bytes on the response side was considered
the optimum trade-off between defender and attacker cost. The
response block size of 468 was chosen so that 3 blocks of 468 octets
would still comfortably fit into typical Maximum Transmission Unit
(MTU) size values.
Mayrhofer Experimental PAGE 4
RFC 8467 Padding Policies for EDNS(0) October 2018
The block size will interact with the MTU size. Especially for
length values that are a large fraction of the MTU, unless the block
length is chosen so that a multiple just fits into the MTU, Block-
Length Padding may cause unnecessary fragmentation for UDP-based
delivery. Of course, choosing a block length larger than the MTU
always forces fragmentation.
Note: Once DNSSEC-validating clients become more prevalent, observed
size patterns are expected to change significantly. In that case,
the recommended strategy might need to be revisited.
4.2. Other Strategies
4.2.1. Maximal-Length Padding
In Maximal-Length Padding, the sender pads every message to the
maximum size allowed by protocol negotiations.
Advantages: Maximal-Length Padding, when combined with encrypted
transport, provides the highest possible level of message-size
confidentiality.
Disadvantages: Maximal-Length Padding is wasteful and requires
resources on the client, all intervening networks and equipment, and
the server. Depending on the negotiated size, this strategy will
commonly exceed the MTU and result in a consistent number of
fragments, reducing delivery probability when datagram-based
transport (such as UDP) is used.
Due to resource consumption, Maximal-Length Padding is NOT
RECOMMENDED.
4.2.2. Random-Length Padding
When using Random-Length Padding, a sender pads each message with a
random amount of padding. Due to the size of the "Padding" option
itself, each message size is increased by at least 4 octets. The
upper limit for padding is the maximum message size. However, a
client or server may choose to impose a lower maximum padding length.
Options: Maximum and minimum padding length.
Advantages: Theoretically, this policy should create a natural
distribution of message sizes.
Disadvantage: Random-Length Padding allows an attacker who can
observe a large number of requests to infer the length of the
original value by observing the distribution of total lengths.
Mayrhofer Experimental PAGE 5
RFC 8467 Padding Policies for EDNS(0) October 2018
According to the limited empirical data available, Random-Length
Padding exposes slightly more entropy to an attacker than Block-
Length Padding. Because of that, and the risk outlined above,
Random-Length Padding is NOT RECOMMENDED.
4.2.3. Random-Block-Length Padding
This policy combines Block-Length Padding with a random component.
Specifically, a sender randomly chooses between a few block length
values and then applies Block-Length Padding based on the chosen
block length. The random selection of block length might even be
reasonably based on a "weak" source of randomness, such as the
transaction ID of the message.
Options: Number of and the values for the set of block lengths;
source of randomness
Advantages: Compared to Block-Length Padding, this creates more
variety in the resulting message sizes for a certain individual
original message length.
Disadvantage: Requires more implementation effort compared to simple
Block-Length Padding.
Random-Block-Length Padding requires further empirical study, as do
other combinations of padding strategies.
5. IANA Considerations
This document has no IANA actions.
6. Security Considerations
The choice of the right padding policy (and the right parameters for
the chosen policy) has a significant impact on the resilience of
encrypted DNS against size-based correlation attacks. Therefore, any
implementor of the "Padding" option must carefully consider which
policies to implement, the default policy chosen, which parameters to
make configurable, and the default parameter values.
No matter how carefully a client selects their padding policy, this
effort can be jeopardized if the server chooses to apply an
ineffective padding policy to the corresponding response packets.
Therefore, a client applying the "Padding" option may want to choose
a DNS server that applies a padding policy on responses that is at
least equally effective.
Mayrhofer Experimental PAGE 6
RFC 8467 Padding Policies for EDNS(0) October 2018
Note that even with encryption and padding, it might be trivial to
identify that the observed traffic is DNS. Also, padding does not
prevent information leaks via other side channels (particularly
timing information and number of query/response pairs).
Countermeasures against such side channels could include injecting
artificial "cover traffic" into the stream of DNS messages or
delaying DNS responses by a certain amount of jitter. Such
strategies are out of the scope of this document. Additionally,
there is not enough theoretic analysis or experimental data available
to recommend any such countermeasures.
7. References
7.1. Normative References
[NDSS-PADDING]
Gillmor, D., "Empirical DNS Padding Policy", March 2017,
<https://dns.cmrg.net/
ndss2017-dprive-empirical-DNS-traffic-size.pdf>.
[RFC 2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC 2119, March 1997,
<https://www.rfc-editor.org/info/RFC 2119>.
[RFC 7830] Mayrhofer, A., "The EDNS(0) Padding Option", RFC 7830,
DOI 10.17487/RFC 7830, May 2016,
<https://www.rfc-editor.org/info/RFC 7830>.
[RFC 8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC 8174,
May 2017, <https://www.rfc-editor.org/info/RFC 8174>.
7.2. Informative References
[RFC 7858] Hu, Z., Zhu, L., Heidemann, J., Mankin, A., Wessels, D.,
and P. Hoffman, "Specification for DNS over Transport
Layer Security (TLS)", RFC 7858, DOI 10.17487/RFC 7858, May
2016, <https://www.rfc-editor.org/info/RFC 7858>.
[RFC 8094] Reddy, T., Wing, D., and P. Patil, "DNS over Datagram
Transport Layer Security (DTLS)", RFC 8094,
DOI 10.17487/RFC 8094, February 2017,
<https://www.rfc-editor.org/info/RFC 8094>.
Mayrhofer Experimental PAGE 7
RFC 8467 Padding Policies for EDNS(0) October 2018
Appendix A. Padding Policies That Are Not Sensible
A.1. No Padding
In the No Padding policy, the "Padding" option is not used, and the
size of the final (actually, "non-padded") message obviously exactly
matches the size of the unpadded message. Even though this
"non-policy" seems redundant in this list, its properties must be
considered for cases in which just one of the parties (client or
server) applies padding.
Also, this policy is required when the remaining message size of the
unpadded message does not allow for the "Padding" option to be
included -- i.e., there are fewer than 4 octets left.
Advantages: This policy requires no additional resources on the
client, server, and network side.
Disadvantages: The original size of the message remains unchanged;
hence, this approach provides no additional confidentiality.
The No Padding policy MUST NOT be used unless message size disallows
the use of the "Padding" option.
A.2. Fixed-Length Padding
In Fixed-Length Padding, a sender chooses to pad each message with a
padding of constant length.
Options: Actual length of padding
Advantages: Since the padding is constant in length, this policy is
very easy to implement and at least ensures that the message length
diverges from the length of the original packet (even if only by a
fixed value).
Disadvantage: Obviously, the amount of padding is easily discoverable
from a single unencrypted message or by observing message patterns.
When a public DNS server applies this policy, the length of the
padding hence must be assumed to be public knowledge. Therefore,
this policy is (almost) as useless as the No Padding policy described
above.
The Fixed-Length Padding policy MUST NOT be used except for test
applications.
Mayrhofer Experimental PAGE 8
RFC 8467 Padding Policies for EDNS(0) October 2018
Acknowledgements
Daniel K. Gillmor performed empirical research out of which the
"Recommended Strategy" was copied. Stephane Bortzmeyer and Hugo
Connery provided text. Shane Kerr, Sara Dickinson, Paul Hoffman,
Magnus Westerlund, Charlie Kaufman, Joe Clarke, and Meral Shirazipour
performed reviews or provided substantial comments.
Author's Address
Alexander Mayrhofer
nic.at GmbH
Karlsplatz 1/2/9
Vienna 1010
Austria
Email: alex.mayrhofer.ietf@gmail.com
URI: http://edns0-padding.org/
Mayrhofer Experimental PAGE 9
Padding Policies for Extension Mechanisms for DNS (EDNS(0))
RFC TOTAL SIZE: 19435 bytes
PUBLICATION DATE: Saturday, October 13th, 2018
LEGAL RIGHTS: The IETF Trust (see BCP 78)
|
