|
|
|
|
|
|
IETF RFC 8343
A YANG Data Model for Interface Management
Last modified on Friday, March 16th, 2018
 Permanent link to RFC 8343
 Search GitHub Wiki for RFC 8343
 Show other RFCs mentioning RFC 8343
Internet Engineering Task Force (IETF) M. Bjorklund
Request for Comments: 8343 Tail-f Systems
Obsoletes: 7223 March 2018
Category: Standards Track
ISSN: 2070-1721
A YANG Data Model for Interface Management
 Abstract
This document defines a YANG data model for the management of network
interfaces. It is expected that interface-type-specific data models
augment the generic interfaces data model defined in this document.
The data model includes definitions for configuration and system
state (status information and counters for the collection of
statistics).
The YANG data model in this document conforms to the Network
Management Datastore Architecture (NMDA) defined in RFC 8342.
This document obsoletes RFC 7223.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/RFC 8343.
Bjorklund Standards Track PAGE 1 
RFC 8343 YANG Interface Management March 2018
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
1.1. Summary of Changes from RFC 7223 ...........................3
1.2. Terminology ................................................3
1.3. Tree Diagrams ..............................................4
2. Objectives ......................................................5
3. Interfaces Data Model ...........................................5
3.1. The Interface List .........................................6
3.2. Interface References .......................................8
3.3. Interface Layering .........................................8
4. Relationship to the IF-MIB ......................................9
5. Interfaces YANG Module .........................................10
6. IANA Considerations ............................................34
7. Security Considerations ........................................35
8. References .....................................................36
8.1. Normative References ......................................36
8.2. Informative References ....................................37
Appendix A. Example: Ethernet Interface Module ...................38
Appendix B. Example: Ethernet Bonding Interface Module ...........39
Appendix C. Example: VLAN Interface Module .......................40
Appendix D. Example: NETCONF <get-config> Reply ..................41
Appendix E. Example: NETCONF <get-data> Reply ....................42
Appendix F. Examples: Interface Naming Schemes ...................44
F.1. Router with Restricted Interface Names ....................44
F.2. Router with Arbitrary Interface Names .....................45
F.3. Ethernet Switch with Restricted Interface Names ...........46
F.4. Generic Host with Restricted Interface Names ..............47
F.5. Generic Host with Arbitrary Interface Names ...............48
Acknowledgments ...................................................49
Author's Address ..................................................49
Bjorklund Standards Track PAGE 2
RFC 8343 YANG Interface Management March 2018
1. Introduction
This document defines a YANG data model [RFC 7950] for the management
of network interfaces. It is expected that interface-type-specific
data models will augment the generic interfaces data model defined in
this document.
Network interfaces are central to the management of many Internet
protocols. Thus, it is important to establish a common data model
for how interfaces are identified, configured, and monitored.
The data model includes configuration data and state data (status
information and counters for the collection of statistics).
This version of the interfaces data model supports the Network
Management Datastore Architecture (NMDA) [RFC 8342].
1.1. Summary of Changes from RFC 7223
The "/interfaces-state" subtree with "config false" data nodes is
deprecated. All "config false" data nodes are now present in the
"/interfaces" subtree.
Servers that do not implement NMDA, or that wish to support clients
that do not implement NMDA, MAY implement the deprecated
"/interfaces-state" tree.
1.2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC 2119] [RFC 8174] when, and only when, they appear in all
capitals, as shown here.
The following terms are used within this document:
o system-controlled interface: An interface is said to be system-
controlled if the system creates and deletes the interface
independently of what has been explicitly configured. Examples
are interfaces representing physical hardware that appear and
disappear when hardware (e.g., a line card or hot-pluggable
wireless interface) is added or removed. System-controlled
interfaces may also appear if a certain functionality is enabled
(e.g., a loopback interface might appear if the IP protocol stack
is enabled).
Bjorklund Standards Track PAGE 3
RFC 8343 YANG Interface Management March 2018
o user-controlled interface: An interface is said to be user-
controlled if the creation of the interface is controlled by
adding explicit interface configuration to the intended
configuration and the removal of the interface is controlled by
removing explicit interface configuration from the intended
configuration. Examples are VLAN interfaces configured on a
system-controlled Ethernet interface.
The following terms are defined in [RFC 8342] and are not redefined
here:
o client
o server
o configuration
o system state
o operational state
o intended configuration
o running configuration datastore
o operational state datastore
The following terms are defined in [RFC 7950] and are not redefined
here:
o augment
o data model
o data node
1.3. Tree Diagrams
Tree diagrams used in this document follow the notation defined in
[RFC 8340].
Bjorklund Standards Track PAGE 4
RFC 8343 YANG Interface Management March 2018
2. Objectives
This section describes some of the design objectives for the model
presented in Section 5.
o It is recognized that existing implementations will have to map
the interface data model defined in this memo to their proprietary
native data model. To facilitate such mappings, the data model
should be simple.
o The data model should be suitable for new implementations to use
as is, without requiring a mapping to a different native model.
o References to interfaces should be as simple as possible,
preferably by using a single leafref.
o The mapping to ifIndex [RFC 2863] used by the Simple Network
Management Protocol (SNMP) to identify interfaces must be clear.
o The model must support interface layering: both (1) simple
layering, where one interface is layered on top of exactly one
other interface, and (2) more complex scenarios, where one
interface results from the aggregation of N other interfaces or
when N interfaces are multiplexed over one other interface.
o The data model should support the pre-provisioning of interface
configuration; that is, it should be possible to configure an
interface whose physical interface hardware is not present on the
device. It is recommended that devices that support dynamic
addition and removal of physical interfaces also support
pre-provisioning.
o The data model should support physical interfaces as well as
logical interfaces.
o The data model should include read-only counters in order to
gather statistics for sent and received octets and packets,
received packets with errors, and packets that could not be sent
due to errors.
3. Interfaces Data Model
This document defines the YANG module "ietf-interfaces", which has
the following structure, excluding the deprecated "/interfaces-state"
subtree:
Bjorklund Standards Track PAGE 5
RFC 8343 YANG Interface Management March 2018
module: ietf-interfaces
+--rw interfaces
+--rw interface* [name]
+--rw name string
+--rw description? string
+--rw type identityref
+--rw enabled? boolean
+--rw link-up-down-trap-enable? enumeration {if-mib}?
+--ro admin-status enumeration {if-mib}?
+--ro oper-status enumeration
+--ro last-change? yang:date-and-time
+--ro if-index int32 {if-mib}?
+--ro phys-address? yang:phys-address
+--ro higher-layer-if* interface-ref
+--ro lower-layer-if* interface-ref
+--ro speed? yang:gauge64
+--ro statistics
+--ro discontinuity-time yang:date-and-time
+--ro in-octets? yang:counter64
+--ro in-unicast-pkts? yang:counter64
+--ro in-broadcast-pkts? yang:counter64
+--ro in-multicast-pkts? yang:counter64
+--ro in-discards? yang:counter32
+--ro in-errors? yang:counter32
+--ro in-unknown-protos? yang:counter32
+--ro out-octets? yang:counter64
+--ro out-unicast-pkts? yang:counter64
+--ro out-broadcast-pkts? yang:counter64
+--ro out-multicast-pkts? yang:counter64
+--ro out-discards? yang:counter32
+--ro out-errors? yang:counter32
3.1. The Interface List
The data model for interfaces presented in this document uses a flat
list of interfaces ("/interfaces/interface"). Each interface in the
list is identified by its name. Furthermore, each interface has a
mandatory "type" leaf.
The "iana-if-type" module [RFC 7224] defines YANG identities for the
interface types in the IANA-maintained "ifType definitions" registry.
It is expected that interface-type-specific data models augment the
interface list and possibly use the "type" leaf to make the
augmentation conditional.
Bjorklund Standards Track PAGE 6
RFC 8343 YANG Interface Management March 2018
As an example of such an interface-type-specific augmentation,
consider this YANG snippet. For a more complete example, see
Appendix A.
import interfaces {
prefix "if";
}
import iana-if-type {
prefix ianaift;
}
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ethernetCsmacd'";
container ethernet {
leaf duplex {
...
}
}
}
For system-controlled interfaces, the "name" is the device-specific
name of the interface.
If the device supports arbitrarily named user-controlled interfaces,
then the server will advertise the "arbitrary-names" feature. If the
server does not advertise this feature, the names of user-controlled
interfaces MUST match the device's naming scheme. How a client can
learn the naming scheme of such devices is outside the scope of this
document. See Appendices F.1 and F.2 for examples.
When a system-controlled interface is created in the operational
state by the system, the system tries to apply the interface
configuration in the intended configuration with the same name as the
new interface. If no such interface configuration is found, or if
the configured type does not match the real interface type, the
system creates the interface without applying explicit configuration.
When a user-controlled interface is created, the configuration
determines the name of the interface.
Depending on the operating system and the physical attachment point
to which a network interface may be attached or removed, it may be
impossible for an implementation to provide predictable and
consistent names for system-controlled interfaces across insertion/
removal cycles as well as in anticipation of initial insertion. The
ability to provide configurations for such interfaces is therefore
dependent on the implementation and cannot be assumed in all cases.
Bjorklund Standards Track PAGE 7
RFC 8343 YANG Interface Management March 2018
3.2. Interface References
An interface is identified by its name, which is unique within the
server. This property is captured in the "interface-ref" typedef,
which other YANG modules SHOULD use when they need to reference an
interface.
3.3. Interface Layering
There is no generic mechanism for how an interface is configured to
be layered on top of some other interface. It is expected that
interface-type-specific models define their own data nodes for
interface layering by using "interface-ref" types to reference lower
layers.
Below is an example of a model with such nodes. For a more complete
example, see Appendix B.
import interfaces {
prefix "if";
}
import iana-if-type {
prefix ianaift;
}
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ieee8023adLag'";
leaf-list slave-if {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'ianaift:ethernetCsmacd'" {
description
"The type of a slave interface must be
'ethernetCsmacd'.";
}
}
// other bonding config params, failover times, etc.
}
While the interface layering is configured in interface-type-specific
models, two generic state data leaf-lists, "higher-layer-if" and
"lower-layer-if", represent a read-only view of the interface
layering hierarchy.
Bjorklund Standards Track PAGE 8
RFC 8343 YANG Interface Management March 2018
4. Relationship to the IF-MIB
If the device implements the IF-MIB [RFC 2863], each entry in the
"/interfaces/interface" list in the operational state is typically
mapped to one ifEntry. The "if-index" leaf MUST contain the value of
the corresponding ifEntry's ifIndex.
In most cases, the "name" of an "/interfaces/interface" entry is
mapped to ifName. The IF-MIB allows two different ifEntries to have
the same ifName. Devices that support this feature and also support
the data model defined in this document cannot have a 1-1 mapping
between the "name" leaf and ifName.
The configured "description" of an "interface" has traditionally been
mapped to ifAlias in some implementations. This document allows this
mapping, but implementers should be aware of the differences in the
value space and persistence for these objects. See the YANG module
definition of the leaf "description" in Section 5 for details.
The IF-MIB also defines the writable object ifPromiscuousMode. Since
this object typically is not implemented as a configuration object by
SNMP agents, it is not mapped to the "ietf-interfaces" module.
The ifMtu object from the IF-MIB is not mapped to the
"ietf-interfaces" module. It is expected that interface-type-
specific YANG modules provide interface-type-specific MTU leafs by
augmenting the "ietf-interfaces" model.
There are a number of counters in the IF-MIB that exist in two
versions: one with 32 bits and one with 64 bits. The 64-bit versions
were added to support high-speed interfaces with a data rate greater
than 20,000,000 bits/second. Today's implementations generally
support such high-speed interfaces; hence, only 64-bit counters are
provided in this data model. Note that the server that implements
this module and an SNMP agent may differ in the time granularity in
which they provide access to the counters. For example, it is common
that SNMP implementations cache counter values for some time.
The objects ifDescr and ifConnectorPresent from the IF-MIB are not
mapped to the "ietf-interfaces" module.
The following table lists the YANG data nodes with corresponding
objects in the IF-MIB.
Bjorklund Standards Track PAGE 9
RFC 8343 YANG Interface Management March 2018
+--------------------------------------+----------------------------+
| YANG data node in | IF-MIB object |
| /interfaces/interface | |
+--------------------------------------+----------------------------+
| name | ifName |
| type | ifType |
| description | ifAlias |
| admin-status | ifAdminStatus |
| oper-status | ifOperStatus |
| last-change | ifLastChange |
| if-index | ifIndex |
| link-up-down-trap-enable | ifLinkUpDownTrapEnable |
| phys-address | ifPhysAddress |
| higher-layer-if and lower-layer-if | ifStackTable |
| speed | ifSpeed and ifHighSpeed |
| discontinuity-time | ifCounterDiscontinuityTime |
| in-octets | ifHCInOctets |
| in-unicast-pkts | ifHCInUcastPkts |
| in-broadcast-pkts | ifHCInBroadcastPkts |
| in-multicast-pkts | ifHCInMulticastPkts |
| in-discards | ifInDiscards |
| in-errors | ifInErrors |
| in-unknown-protos | ifInUnknownProtos |
| out-octets | ifHCOutOctets |
| out-unicast-pkts | ifHCOutUcastPkts |
| out-broadcast-pkts | ifHCOutBroadcastPkts |
| out-multicast-pkts | ifHCOutMulticastPkts |
| out-discards | ifOutDiscards |
| out-errors | ifOutErrors |
+--------------------------------------+----------------------------+
YANG Data Nodes and Related IF-MIB Objects
5. Interfaces YANG Module
This YANG module imports typedefs from [RFC 6991].
<CODE BEGINS> file "ietf-interfaces@2018-02-20.yang"
module ietf-interfaces {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-interfaces";
prefix if;
import ietf-yang-types {
prefix yang;
}
Bjorklund Standards Track PAGE 10
RFC 8343 YANG Interface Management March 2018
organization
"IETF NETMOD (Network Modeling) Working Group";
contact
"WG Web: <https://datatracker.ietf.org/wg/netmod/>
WG List: <mailto:netmod@ietf.org>
Editor: Martin Bjorklund
<mailto:mbj@tail-f.com>";
description
"This module contains a collection of YANG definitions for
managing network interfaces.
Copyright (c) 2018 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC 8343; see
the RFC itself for full legal notices.";
revision 2018-02-20 {
description
"Updated to support NMDA.";
reference
"RFC 8343: A YANG Data Model for Interface Management";
}
revision 2014-05-08 {
description
"Initial revision.";
reference
"RFC 7223: A YANG Data Model for Interface Management";
}
/*
* Typedefs
*/
typedef interface-ref {
type leafref {
path "/if:interfaces/if:interface/if:name";
Bjorklund Standards Track PAGE 11
RFC 8343 YANG Interface Management March 2018
}
description
"This type is used by data models that need to reference
interfaces.";
}
/*
* Identities
*/
identity interface-type {
description
"Base identity from which specific interface types are
derived.";
}
/*
* Features
*/
feature arbitrary-names {
description
"This feature indicates that the device allows user-controlled
interfaces to be named arbitrarily.";
}
feature pre-provisioning {
description
"This feature indicates that the device supports
pre-provisioning of interface configuration, i.e., it is
possible to configure an interface whose physical interface
hardware is not present on the device.";
}
feature if-mib {
description
"This feature indicates that the device implements
the IF-MIB.";
reference
"RFC 2863: The Interfaces Group MIB";
}
/*
* Data nodes
*/
container interfaces {
description
"Interface parameters.";
Bjorklund Standards Track PAGE 12
RFC 8343 YANG Interface Management March 2018
list interface {
key "name";
description
"The list of interfaces on the device.
The status of an interface is available in this list in the
operational state. If the configuration of a
system-controlled interface cannot be used by the system
(e.g., the interface hardware present does not match the
interface type), then the configuration is not applied to
the system-controlled interface shown in the operational
state. If the configuration of a user-controlled interface
cannot be used by the system, the configured interface is
not instantiated in the operational state.
System-controlled interfaces created by the system are
always present in this list in the operational state,
whether or not they are configured.";
leaf name {
type string;
description
"The name of the interface.
A device MAY restrict the allowed values for this leaf,
possibly depending on the type of the interface.
For system-controlled interfaces, this leaf is the
device-specific name of the interface.
If a client tries to create configuration for a
system-controlled interface that is not present in the
operational state, the server MAY reject the request if
the implementation does not support pre-provisioning of
interfaces or if the name refers to an interface that can
never exist in the system. A Network Configuration
Protocol (NETCONF) server MUST reply with an rpc-error
with the error-tag 'invalid-value' in this case.
If the device supports pre-provisioning of interface
configuration, the 'pre-provisioning' feature is
advertised.
If the device allows arbitrarily named user-controlled
interfaces, the 'arbitrary-names' feature is advertised.
Bjorklund Standards Track PAGE 13
RFC 8343 YANG Interface Management March 2018
When a configured user-controlled interface is created by
the system, it is instantiated with the same name in the
operational state.
A server implementation MAY map this leaf to the ifName
MIB object. Such an implementation needs to use some
mechanism to handle the differences in size and characters
allowed between this leaf and ifName. The definition of
such a mechanism is outside the scope of this document.";
reference
"RFC 2863: The Interfaces Group MIB - ifName";
}
leaf description {
type string;
description
"A textual description of the interface.
A server implementation MAY map this leaf to the ifAlias
MIB object. Such an implementation needs to use some
mechanism to handle the differences in size and characters
allowed between this leaf and ifAlias. The definition of
such a mechanism is outside the scope of this document.
Since ifAlias is defined to be stored in non-volatile
storage, the MIB implementation MUST map ifAlias to the
value of 'description' in the persistently stored
configuration.";
reference
"RFC 2863: The Interfaces Group MIB - ifAlias";
}
leaf type {
type identityref {
base interface-type;
}
mandatory true;
description
"The type of the interface.
When an interface entry is created, a server MAY
initialize the type leaf with a valid value, e.g., if it
is possible to derive the type from the name of the
interface.
If a client tries to set the type of an interface to a
value that can never be used by the system, e.g., if the
type is not supported or if the type does not match the
Bjorklund Standards Track PAGE 14
RFC 8343 YANG Interface Management March 2018
name of the interface, the server MUST reject the request.
A NETCONF server MUST reply with an rpc-error with the
error-tag 'invalid-value' in this case.";
reference
"RFC 2863: The Interfaces Group MIB - ifType";
}
leaf enabled {
type boolean;
default "true";
description
"This leaf contains the configured, desired state of the
interface.
Systems that implement the IF-MIB use the value of this
leaf in the intended configuration to set
IF-MIB.ifAdminStatus to 'up' or 'down' after an ifEntry
has been initialized, as described in RFC 2863.
Changes in this leaf in the intended configuration are
reflected in ifAdminStatus.";
reference
"RFC 2863: The Interfaces Group MIB - ifAdminStatus";
}
leaf link-up-down-trap-enable {
if-feature if-mib;
type enumeration {
enum enabled {
value 1;
description
"The device will generate linkUp/linkDown SNMP
notifications for this interface.";
}
enum disabled {
value 2;
description
"The device will not generate linkUp/linkDown SNMP
notifications for this interface.";
}
}
description
"Controls whether linkUp/linkDown SNMP notifications
should be generated for this interface.
Bjorklund Standards Track PAGE 15
RFC 8343 YANG Interface Management March 2018
If this node is not configured, the value 'enabled' is
operationally used by the server for interfaces that do
not operate on top of any other interface (i.e., there are
no 'lower-layer-if' entries), and 'disabled' otherwise.";
reference
"RFC 2863: The Interfaces Group MIB -
ifLinkUpDownTrapEnable";
}
leaf admin-status {
if-feature if-mib;
type enumeration {
enum up {
value 1;
description
"Ready to pass packets.";
}
enum down {
value 2;
description
"Not ready to pass packets and not in some test mode.";
}
enum testing {
value 3;
description
"In some test mode.";
}
}
config false;
mandatory true;
description
"The desired state of the interface.
This leaf has the same read semantics as ifAdminStatus.";
reference
"RFC 2863: The Interfaces Group MIB - ifAdminStatus";
}
leaf oper-status {
type enumeration {
enum up {
value 1;
description
"Ready to pass packets.";
}
enum down {
value 2;
Bjorklund Standards Track PAGE 16
RFC 8343 YANG Interface Management March 2018
description
"The interface does not pass any packets.";
}
enum testing {
value 3;
description
"In some test mode. No operational packets can
be passed.";
}
enum unknown {
value 4;
description
"Status cannot be determined for some reason.";
}
enum dormant {
value 5;
description
"Waiting for some external event.";
}
enum not-present {
value 6;
description
"Some component (typically hardware) is missing.";
}
enum lower-layer-down {
value 7;
description
"Down due to state of lower-layer interface(s).";
}
}
config false;
mandatory true;
description
"The current operational state of the interface.
This leaf has the same semantics as ifOperStatus.";
reference
"RFC 2863: The Interfaces Group MIB - ifOperStatus";
}
leaf last-change {
type yang:date-and-time;
config false;
description
"The time the interface entered its current operational
state. If the current state was entered prior to the
last re-initialization of the local network management
subsystem, then this node is not present.";
Bjorklund Standards Track PAGE 17
RFC 8343 YANG Interface Management March 2018
reference
"RFC 2863: The Interfaces Group MIB - ifLastChange";
}
leaf if-index {
if-feature if-mib;
type int32 {
range "1..2147483647";
}
config false;
mandatory true;
description
"The ifIndex value for the ifEntry represented by this
interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifIndex";
}
leaf phys-address {
type yang:phys-address;
config false;
description
"The interface's address at its protocol sub-layer. For
example, for an 802.x interface, this object normally
contains a Media Access Control (MAC) address. The
interface's media-specific modules must define the bit
and byte ordering and the format of the value of this
object. For interfaces that do not have such an address
(e.g., a serial line), this node is not present.";
reference
"RFC 2863: The Interfaces Group MIB - ifPhysAddress";
}
leaf-list higher-layer-if {
type interface-ref;
config false;
description
"A list of references to interfaces layered on top of this
interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifStackTable";
}
leaf-list lower-layer-if {
type interface-ref;
config false;
Bjorklund Standards Track PAGE 18
RFC 8343 YANG Interface Management March 2018
description
"A list of references to interfaces layered underneath this
interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifStackTable";
}
leaf speed {
type yang:gauge64;
units "bits/second";
config false;
description
"An estimate of the interface's current bandwidth in bits
per second. For interfaces that do not vary in
bandwidth or for those where no accurate estimation can
be made, this node should contain the nominal bandwidth.
For interfaces that have no concept of bandwidth, this
node is not present.";
reference
"RFC 2863: The Interfaces Group MIB -
ifSpeed, ifHighSpeed";
}
container statistics {
config false;
description
"A collection of interface-related statistics objects.";
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
description
"The time on the most recent occasion at which any one or
more of this interface's counters suffered a
discontinuity. If no such discontinuities have occurred
since the last re-initialization of the local management
subsystem, then this node contains the time the local
management subsystem re-initialized itself.";
}
leaf in-octets {
type yang:counter64;
description
"The total number of octets received on the interface,
including framing characters.
Bjorklund Standards Track PAGE 19
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCInOctets";
}
leaf in-unicast-pkts {
type yang:counter64;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were not addressed to a
multicast or broadcast address at this sub-layer.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCInUcastPkts";
}
leaf in-broadcast-pkts {
type yang:counter64;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were addressed to a broadcast
address at this sub-layer.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCInBroadcastPkts";
}
leaf in-multicast-pkts {
type yang:counter64;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were addressed to a multicast
address at this sub-layer. For a MAC-layer protocol,
this includes both Group and Functional addresses.
Bjorklund Standards Track PAGE 20
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCInMulticastPkts";
}
leaf in-discards {
type yang:counter32;
description
"The number of inbound packets that were chosen to be
discarded even though no errors had been detected to
prevent their being deliverable to a higher-layer
protocol. One possible reason for discarding such a
packet could be to free up buffer space.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInDiscards";
}
leaf in-errors {
type yang:counter32;
description
"For packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from being
deliverable to a higher-layer protocol. For character-
oriented or fixed-length interfaces, the number of
inbound transmission units that contained errors
preventing them from being deliverable to a higher-layer
protocol.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInErrors";
}
leaf in-unknown-protos {
type yang:counter32;
Bjorklund Standards Track PAGE 21
RFC 8343 YANG Interface Management March 2018
description
"For packet-oriented interfaces, the number of packets
received via the interface that were discarded because
of an unknown or unsupported protocol. For
character-oriented or fixed-length interfaces that
support protocol multiplexing, the number of
transmission units received via the interface that were
discarded because of an unknown or unsupported protocol.
For any interface that does not support protocol
multiplexing, this counter is not present.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInUnknownProtos";
}
leaf out-octets {
type yang:counter64;
description
"The total number of octets transmitted out of the
interface, including framing characters.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCOutOctets";
}
leaf out-unicast-pkts {
type yang:counter64;
description
"The total number of packets that higher-level protocols
requested be transmitted and that were not addressed
to a multicast or broadcast address at this sub-layer,
including those that were discarded or not sent.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCOutUcastPkts";
Bjorklund Standards Track PAGE 22
RFC 8343 YANG Interface Management March 2018
}
leaf out-broadcast-pkts {
type yang:counter64;
description
"The total number of packets that higher-level protocols
requested be transmitted and that were addressed to a
broadcast address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCOutBroadcastPkts";
}
leaf out-multicast-pkts {
type yang:counter64;
description
"The total number of packets that higher-level protocols
requested be transmitted and that were addressed to a
multicast address at this sub-layer, including those
that were discarded or not sent. For a MAC-layer
protocol, this includes both Group and Functional
addresses.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCOutMulticastPkts";
}
leaf out-discards {
type yang:counter32;
description
"The number of outbound packets that were chosen to be
discarded even though no errors had been detected to
prevent their being transmitted. One possible reason
for discarding such a packet could be to free up buffer
space.
Bjorklund Standards Track PAGE 23
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifOutDiscards";
}
leaf out-errors {
type yang:counter32;
description
"For packet-oriented interfaces, the number of outbound
packets that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifOutErrors";
}
}
}
}
/*
* Legacy typedefs
*/
typedef interface-state-ref {
type leafref {
path "/if:interfaces-state/if:interface/if:name";
}
status deprecated;
description
"This type is used by data models that need to reference
the operationally present interfaces.";
}
/*
* Legacy operational state data nodes
*/
container interfaces-state {
Bjorklund Standards Track PAGE 24
RFC 8343 YANG Interface Management March 2018
config false;
status deprecated;
description
"Data nodes for the operational state of interfaces.";
list interface {
key "name";
status deprecated;
description
"The list of interfaces on the device.
System-controlled interfaces created by the system are
always present in this list, whether or not they are
configured.";
leaf name {
type string;
status deprecated;
description
"The name of the interface.
A server implementation MAY map this leaf to the ifName
MIB object. Such an implementation needs to use some
mechanism to handle the differences in size and characters
allowed between this leaf and ifName. The definition of
such a mechanism is outside the scope of this document.";
reference
"RFC 2863: The Interfaces Group MIB - ifName";
}
leaf type {
type identityref {
base interface-type;
}
mandatory true;
status deprecated;
description
"The type of the interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifType";
}
leaf admin-status {
if-feature if-mib;
type enumeration {
enum up {
value 1;
Bjorklund Standards Track PAGE 25
RFC 8343 YANG Interface Management March 2018
description
"Ready to pass packets.";
}
enum down {
value 2;
description
"Not ready to pass packets and not in some test mode.";
}
enum testing {
value 3;
description
"In some test mode.";
}
}
mandatory true;
status deprecated;
description
"The desired state of the interface.
This leaf has the same read semantics as ifAdminStatus.";
reference
"RFC 2863: The Interfaces Group MIB - ifAdminStatus";
}
leaf oper-status {
type enumeration {
enum up {
value 1;
description
"Ready to pass packets.";
}
enum down {
value 2;
description
"The interface does not pass any packets.";
}
enum testing {
value 3;
description
"In some test mode. No operational packets can
be passed.";
}
enum unknown {
value 4;
description
"Status cannot be determined for some reason.";
}
enum dormant {
Bjorklund Standards Track PAGE 26
RFC 8343 YANG Interface Management March 2018
value 5;
description
"Waiting for some external event.";
}
enum not-present {
value 6;
description
"Some component (typically hardware) is missing.";
}
enum lower-layer-down {
value 7;
description
"Down due to state of lower-layer interface(s).";
}
}
mandatory true;
status deprecated;
description
"The current operational state of the interface.
This leaf has the same semantics as ifOperStatus.";
reference
"RFC 2863: The Interfaces Group MIB - ifOperStatus";
}
leaf last-change {
type yang:date-and-time;
status deprecated;
description
"The time the interface entered its current operational
state. If the current state was entered prior to the
last re-initialization of the local network management
subsystem, then this node is not present.";
reference
"RFC 2863: The Interfaces Group MIB - ifLastChange";
}
leaf if-index {
if-feature if-mib;
type int32 {
range "1..2147483647";
}
mandatory true;
status deprecated;
description
"The ifIndex value for the ifEntry represented by this
interface.";
Bjorklund Standards Track PAGE 27
RFC 8343 YANG Interface Management March 2018
reference
"RFC 2863: The Interfaces Group MIB - ifIndex";
}
leaf phys-address {
type yang:phys-address;
status deprecated;
description
"The interface's address at its protocol sub-layer. For
example, for an 802.x interface, this object normally
contains a Media Access Control (MAC) address. The
interface's media-specific modules must define the bit
and byte ordering and the format of the value of this
object. For interfaces that do not have such an address
(e.g., a serial line), this node is not present.";
reference
"RFC 2863: The Interfaces Group MIB - ifPhysAddress";
}
leaf-list higher-layer-if {
type interface-state-ref;
status deprecated;
description
"A list of references to interfaces layered on top of this
interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifStackTable";
}
leaf-list lower-layer-if {
type interface-state-ref;
status deprecated;
description
"A list of references to interfaces layered underneath this
interface.";
reference
"RFC 2863: The Interfaces Group MIB - ifStackTable";
}
leaf speed {
type yang:gauge64;
units "bits/second";
status deprecated;
description
"An estimate of the interface's current bandwidth in bits
per second. For interfaces that do not vary in
bandwidth or for those where no accurate estimation can
Bjorklund Standards Track PAGE 28
RFC 8343 YANG Interface Management March 2018
be made, this node should contain the nominal bandwidth.
For interfaces that have no concept of bandwidth, this
node is not present.";
reference
"RFC 2863: The Interfaces Group MIB -
ifSpeed, ifHighSpeed";
}
container statistics {
status deprecated;
description
"A collection of interface-related statistics objects.";
leaf discontinuity-time {
type yang:date-and-time;
mandatory true;
status deprecated;
description
"The time on the most recent occasion at which any one or
more of this interface's counters suffered a
discontinuity. If no such discontinuities have occurred
since the last re-initialization of the local management
subsystem, then this node contains the time the local
management subsystem re-initialized itself.";
}
leaf in-octets {
type yang:counter64;
status deprecated;
description
"The total number of octets received on the interface,
including framing characters.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCInOctets";
}
leaf in-unicast-pkts {
type yang:counter64;
status deprecated;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were not addressed to a
multicast or broadcast address at this sub-layer.
Bjorklund Standards Track PAGE 29
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCInUcastPkts";
}
leaf in-broadcast-pkts {
type yang:counter64;
status deprecated;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were addressed to a broadcast
address at this sub-layer.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCInBroadcastPkts";
}
leaf in-multicast-pkts {
type yang:counter64;
status deprecated;
description
"The number of packets, delivered by this sub-layer to a
higher (sub-)layer, that were addressed to a multicast
address at this sub-layer. For a MAC-layer protocol,
this includes both Group and Functional addresses.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCInMulticastPkts";
}
leaf in-discards {
type yang:counter32;
status deprecated;
Bjorklund Standards Track PAGE 30
RFC 8343 YANG Interface Management March 2018
description
"The number of inbound packets that were chosen to be
discarded even though no errors had been detected to
prevent their being deliverable to a higher-layer
protocol. One possible reason for discarding such a
packet could be to free up buffer space.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInDiscards";
}
leaf in-errors {
type yang:counter32;
status deprecated;
description
"For packet-oriented interfaces, the number of inbound
packets that contained errors preventing them from being
deliverable to a higher-layer protocol. For character-
oriented or fixed-length interfaces, the number of
inbound transmission units that contained errors
preventing them from being deliverable to a higher-layer
protocol.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInErrors";
}
leaf in-unknown-protos {
type yang:counter32;
status deprecated;
description
"For packet-oriented interfaces, the number of packets
received via the interface that were discarded because
of an unknown or unsupported protocol. For
character-oriented or fixed-length interfaces that
support protocol multiplexing, the number of
transmission units received via the interface that were
discarded because of an unknown or unsupported protocol.
For any interface that does not support protocol
multiplexing, this counter is not present.
Bjorklund Standards Track PAGE 31
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifInUnknownProtos";
}
leaf out-octets {
type yang:counter64;
status deprecated;
description
"The total number of octets transmitted out of the
interface, including framing characters.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCOutOctets";
}
leaf out-unicast-pkts {
type yang:counter64;
status deprecated;
description
"The total number of packets that higher-level protocols
requested be transmitted and that were not addressed
to a multicast or broadcast address at this sub-layer,
including those that were discarded or not sent.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifHCOutUcastPkts";
}
leaf out-broadcast-pkts {
type yang:counter64;
status deprecated;
Bjorklund Standards Track PAGE 32
RFC 8343 YANG Interface Management March 2018
description
"The total number of packets that higher-level protocols
requested be transmitted and that were addressed to a
broadcast address at this sub-layer, including those
that were discarded or not sent.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCOutBroadcastPkts";
}
leaf out-multicast-pkts {
type yang:counter64;
status deprecated;
description
"The total number of packets that higher-level protocols
requested be transmitted and that were addressed to a
multicast address at this sub-layer, including those
that were discarded or not sent. For a MAC-layer
protocol, this includes both Group and Functional
addresses.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB -
ifHCOutMulticastPkts";
}
leaf out-discards {
type yang:counter32;
status deprecated;
description
"The number of outbound packets that were chosen to be
discarded even though no errors had been detected to
prevent their being transmitted. One possible reason
for discarding such a packet could be to free up buffer
space.
Bjorklund Standards Track PAGE 33
RFC 8343 YANG Interface Management March 2018
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifOutDiscards";
}
leaf out-errors {
type yang:counter32;
status deprecated;
description
"For packet-oriented interfaces, the number of outbound
packets that could not be transmitted because of errors.
For character-oriented or fixed-length interfaces, the
number of outbound transmission units that could not be
transmitted because of errors.
Discontinuities in the value of this counter can occur
at re-initialization of the management system and at
other times as indicated by the value of
'discontinuity-time'.";
reference
"RFC 2863: The Interfaces Group MIB - ifOutErrors";
}
}
}
}
}
<CODE ENDS>
6. IANA Considerations
This document registers a URI in the "IETF XML Registry" [RFC 3688].
Following the format in RFC 3688, the following registration has been
made.
URI: urn:ietf:params:xml:ns:yang:ietf-interfaces
Registrant Contact: The IESG.
XML: N/A, the requested URI is an XML namespace.
Bjorklund Standards Track PAGE 34
RFC 8343 YANG Interface Management March 2018
This document registers a YANG module in the "YANG Module Names"
registry [RFC 6020].
name: ietf-interfaces
namespace: urn:ietf:params:xml:ns:yang:ietf-interfaces
prefix: if
reference: RFC 8343
7. Security Considerations
The YANG module specified in this document defines a schema for data
that is designed to be accessed via network management protocols such
as NETCONF [RFC 6241] or RESTCONF [RFC 8040]. The lowest NETCONF layer
is the secure transport layer, and the mandatory-to-implement secure
transport is Secure Shell (SSH) [RFC 6242]. The lowest RESTCONF layer
is HTTPS, and the mandatory-to-implement secure transport is TLS
[RFC 5246].
The NETCONF access control model [RFC 8341] provides the means to
restrict access for particular NETCONF or RESTCONF users to a
preconfigured subset of all available NETCONF or RESTCONF protocol
operations and content.
There are a number of data nodes defined in this YANG module that are
writable/creatable/deletable (i.e., config true, which is the
default). These data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., edit-config)
to these data nodes without proper protection can have a negative
effect on network operations. These are the subtrees and data nodes
and their sensitivity/vulnerability:
/interfaces/interface: This list specifies the configured interfaces
on a device. Unauthorized access to this list could cause the
device to ignore packets it should receive and process.
/interfaces/interface/enabled: This leaf controls whether or not an
interface is enabled. Unauthorized access to this leaf could
cause the device to ignore packets it should receive and process.
Bjorklund Standards Track PAGE 35
RFC 8343 YANG Interface Management March 2018
8. References
8.1. Normative References
[RFC 2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC 2119, March 1997,
<https://www.rfc-editor.org/info/RFC 2119>.
[RFC 2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group
MIB", RFC 2863, DOI 10.17487/RFC 2863, June 2000,
<https://www.rfc-editor.org/info/RFC 2863>.
[RFC 3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC 3688, January 2004,
<https://www.rfc-editor.org/info/RFC 3688>.
[RFC 5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246,
DOI 10.17487/RFC 5246, August 2008,
<https://www.rfc-editor.org/info/RFC 5246>.
[RFC 6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC 6020, October 2010,
<https://www.rfc-editor.org/info/RFC 6020>.
[RFC 6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC 6241, June 2011,
<https://www.rfc-editor.org/info/RFC 6241>.
[RFC 6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC 6242, June 2011,
<https://www.rfc-editor.org/info/RFC 6242>.
[RFC 6991] Schoenwaelder, J., Ed., "Common YANG Data Types",
RFC 6991, DOI 10.17487/RFC 6991, July 2013,
<https://www.rfc-editor.org/info/RFC 6991>.
[RFC 7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC 7950, August 2016,
<https://www.rfc-editor.org/info/RFC 7950>.
[RFC 8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC 8040, January 2017,
<https://www.rfc-editor.org/info/RFC 8040>.
Bjorklund Standards Track PAGE 36
RFC 8343 YANG Interface Management March 2018
[RFC 8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC 8174,
May 2017, <https://www.rfc-editor.org/info/RFC 8174>.
[RFC 8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC 8341, March 2018,
<https://www.rfc-editor.org/info/RFC 8341>.
[RFC 8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC 8342, March 2018,
<https://www.rfc-editor.org/info/RFC 8342>.
8.2. Informative References
[RFC 7224] Bjorklund, M., "IANA Interface Type YANG Module",
RFC 7224, DOI 10.17487/RFC 7224, May 2014,
<https://www.rfc-editor.org/info/RFC 7224>.
[RFC 8340] Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams",
BCP 215, RFC 8340, DOI 10.17487/RFC 8340, March 2018,
<https://www.rfc-editor.org/info/RFC 8340>.
Bjorklund Standards Track PAGE 37
RFC 8343 YANG Interface Management March 2018
Appendix A. Example: Ethernet Interface Module
This section gives a simple example of how an Ethernet interface
module could be defined. It demonstrates how media-specific
configuration parameters can be conditionally augmented to the
generic interface list. It also shows how operational state
parameters can be conditionally augmented to the operational
interface list. The example is not intended as a complete module for
Ethernet configuration.
module example-ethernet {
namespace "http://example.com/ethernet";
prefix "eth";
import ietf-interfaces {
prefix if;
}
import iana-if-type {
prefix ianaift;
}
// configuration and state parameters for Ethernet interfaces
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ethernetCsmacd'";
container ethernet {
container transmission {
choice transmission-params {
case auto {
leaf auto-negotiate {
type empty;
}
}
case manual {
container manual {
leaf duplex {
type enumeration {
enum "half";
enum "full";
}
}
leaf speed {
type enumeration {
enum "10Mb";
enum "100Mb";
enum "1Gb";
enum "10Gb";
}
Bjorklund Standards Track PAGE 38
RFC 8343 YANG Interface Management March 2018
}
}
}
}
leaf duplex {
type enumeration {
enum "half";
enum "full";
}
config false;
}
}
// other Ethernet-specific params...
}
}
}
Appendix B. Example: Ethernet Bonding Interface Module
This section gives an example of how interface layering can be
defined. An Ethernet bonding interface that bonds several Ethernet
interfaces into one logical interface is defined.
module example-ethernet-bonding {
namespace "http://example.com/ethernet-bonding";
prefix "bond";
import ietf-interfaces {
prefix if;
}
import iana-if-type {
prefix ianaift;
}
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ieee8023adLag'";
leaf-list slave-if {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/if:type = 'ianaift:ethernetCsmacd'" {
description
"The type of a slave interface must be 'ethernetCsmacd'.";
}
}
leaf bonding-mode {
type enumeration {
enum round-robin;
Bjorklund Standards Track PAGE 39
RFC 8343 YANG Interface Management March 2018
enum active-backup;
enum broadcast;
}
}
// other bonding config params, failover times, etc.
}
}
Appendix C. Example: VLAN Interface Module
This section gives an example of how a VLAN interface module can be
defined.
module example-vlan {
namespace "http://example.com/vlan";
prefix "vlan";
import ietf-interfaces {
prefix if;
}
import iana-if-type {
prefix ianaift;
}
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:ethernetCsmacd' or
if:type = 'ianaift:ieee8023adLag'";
leaf vlan-tagging {
type boolean;
default false;
}
}
augment "/if:interfaces/if:interface" {
when "if:type = 'ianaift:l2vlan'";
leaf base-interface {
type if:interface-ref;
must "/if:interfaces/if:interface[if:name = current()]"
+ "/vlan:vlan-tagging = 'true'" {
description
"The base interface must have VLAN tagging enabled.";
}
}
leaf vlan-id {
type uint16 {
range "1..4094";
}
Bjorklund Standards Track PAGE 40
RFC 8343 YANG Interface Management March 2018
must "../base-interface" {
description
"If a vlan-id is defined, a base-interface must
be specified.";
}
}
}
}
Appendix D. Example: NETCONF <get-config> Reply
This section gives an example of a reply to the NETCONF <get-config>
request for the running configuration datastore for a device that
implements the example data models above.
<rpc-reply
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"
message-id="101">
<data>
<interfaces
xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces"
xmlns:ianaift="urn:ietf:params:xml:ns:yang:iana-if-type"
xmlns:vlan="http://example.com/vlan">
<interface>
<name>eth0</name>
<type>ianaift:ethernetCsmacd</type>
<enabled>false</enabled>
</interface>
<interface>
<name>eth1</name>
<type>ianaift:ethernetCsmacd</type>
<enabled>true</enabled>
<vlan:vlan-tagging>true</vlan:vlan-tagging>
</interface>
<interface>
<name>eth1.10</name>
<type>ianaift:l2vlan</type>
<enabled>true</enabled>
<vlan:base-interface>eth1</vlan:base-interface>
<vlan:vlan-id>10</vlan:vlan-id>
</interface>
<interface>
<name>lo1</name>
<type>ianaift:softwareLoopback</type>
Bjorklund Standards Track PAGE 41
RFC 8343 YANG Interface Management March 2018
<enabled>true</enabled>
</interface>
</interfaces>
</data>
</rpc-reply>
Appendix E. Example: NETCONF <get-data> Reply
This section gives an example of a reply to the NETCONF <get-data>
request for the operational state datastore for a device that
implements the example data models above.
This example uses the "origin" annotation, which is defined in the
module "ietf-origin" [RFC 8342].
<rpc-reply
xmlns="urn:ietf:params:xml:ns:netconf:base:1.0"
message-id="101">
<data xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-datastores">
<interfaces
xmlns="urn:ietf:params:xml:ns:yang:ietf-interfaces"
xmlns:ianaift="urn:ietf:params:xml:ns:yang:iana-if-type"
xmlns:vlan="http://example.com/vlan"
xmlns:or="urn:ietf:params:xml:ns:yang:ietf-origin">
<interface or:origin="or:intended">
<name>eth0</name>
<type>ianaift:ethernetCsmacd</type>
<enabled>false</enabled>
<admin-status>down</admin-status>
<oper-status>down</oper-status>
<if-index>2</if-index>
<phys-address>00:01:02:03:04:05</phys-address>
<statistics>
<discontinuity-time>
2013-04-01T03:00:00+00:00
</discontinuity-time>
<!-- counters now shown here -->
</statistics>
</interface>
<interface or:origin="or:intended">
<name>eth1</name>
<type>ianaift:ethernetCsmacd</type>
<enabled>true</enabled>
<admin-status>up</admin-status>
<oper-status>up</oper-status>
Bjorklund Standards Track PAGE 42
RFC 8343 YANG Interface Management March 2018
<if-index>7</if-index>
<phys-address>00:01:02:03:04:06</phys-address>
<higher-layer-if>eth1.10</higher-layer-if>
<statistics>
<discontinuity-time>
2013-04-01T03:00:00+00:00
</discontinuity-time>
<!-- counters now shown here -->
</statistics>
<vlan:vlan-tagging>true</vlan:vlan-tagging>
</interface>
<interface or:origin="or:intended">
<name>eth1.10</name>
<type>ianaift:l2vlan</type>
<enabled>true</enabled>
<admin-status>up</admin-status>
<oper-status>up</oper-status>
<if-index>9</if-index>
<lower-layer-if>eth1</lower-layer-if>
<statistics>
<discontinuity-time>
2013-04-01T03:00:00+00:00
</discontinuity-time>
<!-- counters now shown here -->
</statistics>
<vlan:base-interface>eth1</vlan:base-interface>
<vlan:vlan-id>10</vlan:vlan-id>
</interface>
<!-- This interface is not configured -->
<interface or:origin="or:system">
<name>eth2</name>
<type>ianaift:ethernetCsmacd</type>
<admin-status>down</admin-status>
<oper-status>down</oper-status>
<if-index>8</if-index>
<phys-address>00:01:02:03:04:07</phys-address>
<statistics>
<discontinuity-time>
2013-04-01T03:00:00+00:00
</discontinuity-time>
<!-- counters now shown here -->
</statistics>
</interface>
<interface or:origin="or:intended">
<name>lo1</name>
Bjorklund Standards Track PAGE 43
RFC 8343 YANG Interface Management March 2018
<type>ianaift:softwareLoopback</type>
<enabled>true</enabled>
<admin-status>up</admin-status>
<oper-status>up</oper-status>
<if-index>1</if-index>
<statistics>
<discontinuity-time>
2013-04-01T03:00:00+00:00
</discontinuity-time>
<!-- counters now shown here -->
</statistics>
</interface>
</interfaces>
</data>
</rpc-reply>
Appendix F. Examples: Interface Naming Schemes
This section gives examples of some implementation strategies.
The examples make use of the example data model "example-vlan" (see
Appendix C) to show how user-controlled interfaces can be configured.
F.1. Router with Restricted Interface Names
In this example, a router has support for 4 line cards, each with 8
ports. The slots for the cards are physically numbered from 0 to 3,
and the ports on each card from 0 to 7. Each card has Fast Ethernet
or Gigabit Ethernet ports.
The device-specific names for these physical interfaces are
"fastethernet-N/M" or "gigabitethernet-N/M".
The name of a VLAN interface is restricted to the form
"<physical-interface-name>.<subinterface-number>".
It is assumed that the operator is aware of this naming scheme. The
implementation auto-initializes the value for "type" based on the
interface name.
The NETCONF server does not advertise the "arbitrary-names" feature
in the <hello> message.
Bjorklund Standards Track PAGE 44
RFC 8343 YANG Interface Management March 2018
An operator can configure a physical interface by sending an
<edit-config> containing:
<interface nc:operation="create">
<name>fastethernet-1/0</name>
</interface>
When the server processes this request, it will set the leaf "type"
to "ianaift:ethernetCsmacd". Thus, if the client performs a
<get-config> right after the <edit-config> above, it will get:
<interface>
<name>fastethernet-1/0</name>
<type>ianaift:ethernetCsmacd</type>
</interface>
The client can configure a VLAN interface by sending an <edit-config>
containing:
<interface nc:operation="create">
<name>fastethernet-1/0.10005</name>
<type>ianaift:l2vlan</type>
<vlan:base-interface>fastethernet-1/0</vlan:base-interface>
<vlan:vlan-id>5</vlan:vlan-id>
</interface>
If the client tries to change the type of the physical interface with
an <edit-config> containing:
<interface nc:operation="merge">
<name>fastethernet-1/0</name>
<type>ianaift:tunnel</type>
</interface>
then the server will reply with an "invalid-value" error, since the
new type does not match the name.
F.2. Router with Arbitrary Interface Names
In this example, a router has support for 4 line cards, each with 8
ports. The slots for the cards are physically numbered from 0 to 3,
and the ports on each card from 0 to 7. Each card has Fast Ethernet
or Gigabit Ethernet ports.
The device-specific names for these physical interfaces are
"fastethernet-N/M" or "gigabitethernet-N/M".
Bjorklund Standards Track PAGE 45
RFC 8343 YANG Interface Management March 2018
The implementation does not restrict the user-controlled interface
names. This allows an operator to more easily apply the interface
configuration to a different interface. However, the additional
level of indirection also makes it a bit more complex to map
interface names found in other protocols to configuration entries.
The NETCONF server advertises the "arbitrary-names" feature in the
<hello> message.
Physical interfaces are configured as in Appendix F.1.
An operator can configure a VLAN interface by sending an
<edit-config> containing:
<interface nc:operation="create">
<name>acme-interface</name>
<type>ianaift:l2vlan</type>
<vlan:base-interface>fastethernet-1/0</vlan:base-interface>
<vlan:vlan-id>5</vlan:vlan-id>
</interface>
If necessary, the operator can move the configuration named
"acme-interface" over to a different physical interface with an
<edit-config> containing:
<interface nc:operation="merge">
<name>acme-interface</name>
<vlan:base-interface>fastethernet-1/1</vlan:base-interface>
</interface>
F.3. Ethernet Switch with Restricted Interface Names
In this example, an Ethernet switch has a number of ports, each
identified by a simple port number.
The device-specific names for the physical interfaces are numbers
that match the physical port number.
An operator can configure a physical interface by sending an
<edit-config> containing:
<interface nc:operation="create">
<name>6</name>
</interface>
Bjorklund Standards Track PAGE 46
RFC 8343 YANG Interface Management March 2018
When the server processes this request, it will set the leaf "type"
to "ianaift:ethernetCsmacd". Thus, if the client performs a
<get-config> right after the <edit-config> above, it will get:
<interface>
<name>6</name>
<type>ianaift:ethernetCsmacd</type>
</interface>
F.4. Generic Host with Restricted Interface Names
In this example, a generic host has interfaces named by the kernel.
The system identifies the physical interface by the name assigned by
the operating system to the interface.
The name of a VLAN interface is restricted to the form
"<physical-interface-name>:<vlan-number>".
The NETCONF server does not advertise the "arbitrary-names" feature
in the <hello> message.
An operator can configure an interface by sending an <edit-config>
containing:
<interface nc:operation="create">
<name>eth8</name>
</interface>
When the server processes this request, it will set the leaf "type"
to "ianaift:ethernetCsmacd". Thus, if the client performs a
<get-config> right after the <edit-config> above, it will get:
<interface>
<name>eth8</name>
<type>ianaift:ethernetCsmacd</type>
</interface>
The client can configure a VLAN interface by sending an <edit-config>
containing:
<interface nc:operation="create">
<name>eth8:5</name>
<type>ianaift:l2vlan</type>
<vlan:base-interface>eth8</vlan:base-interface>
<vlan:vlan-id>5</vlan:vlan-id>
</interface>
Bjorklund Standards Track PAGE 47
RFC 8343 YANG Interface Management March 2018
F.5. Generic Host with Arbitrary Interface Names
In this example, a generic host has interfaces named by the kernel.
The system identifies the physical interface by the name assigned by
the operating system to the interface.
The implementation does not restrict the user-controlled interface
names. This allows an operator to more easily apply the interface
configuration to a different interface. However, the additional
level of indirection also makes it a bit more complex to map
interface names found in other protocols to configuration entries.
The NETCONF server advertises the "arbitrary-names" feature in the
<hello> message.
Physical interfaces are configured as in Appendix F.4.
An operator can configure a VLAN interface by sending an
<edit-config> containing:
<interface nc:operation="create">
<name>acme-interface</name>
<type>ianaift:l2vlan</type>
<vlan:base-interface>eth8</vlan:base-interface>
<vlan:vlan-id>5</vlan:vlan-id>
</interface>
If necessary, the operator can move the configuration named
"acme-interface" over to a different physical interface with an
<edit-config> containing:
<interface nc:operation="merge">
<name>acme-interface</name>
<vlan:base-interface>eth3</vlan:base-interface>
</interface>
Bjorklund Standards Track PAGE 48
RFC 8343 YANG Interface Management March 2018
Acknowledgments
The author wishes to thank Alexander Clemm, Per Hedeland, Ladislav
Lhotka, and Juergen Schoenwaelder for their helpful comments.
Author's Address
Martin Bjorklund
Tail-f Systems
Email: mbj@tail-f.com
Bjorklund Standards Track PAGE 49
A YANG Data Model for Interface Management
RFC TOTAL SIZE: 91573 bytes
PUBLICATION DATE: Friday, March 16th, 2018
LEGAL RIGHTS: The IETF Trust (see BCP 78)
|
