|
|
|
|
|
|
IETF RFC 8151
Last modified on Friday, May 26th, 2017
 Permanent link to RFC 8151
 Search GitHub Wiki for RFC 8151
 Show other RFCs mentioning RFC 8151
Internet Engineering Task Force (IETF) L. Yong
Request for Comments: 8151 L. Dunbar
Category: Informational Huawei
ISSN: 2070-1721 M. Toy
Verizon
A. Isaac
Juniper Networks
V. Manral
Nano Sec Co
May 2017
Use Cases for Data Center Network Virtualization Overlay Networks
 Abstract
This document describes Network Virtualization over Layer 3 (NVO3)
use cases that can be deployed in various data centers and serve
different data-center applications.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/RFC 8151.
Yong, et al. Informational PAGE 1 
RFC 8151 NVO3 Use Case May 2017
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
1.1. Terminology ................................................4
1.2. NVO3 Background ............................................5
2. DC with a Large Number of Virtual Networks ......................6
3. DC NVO3 Virtual Network and External Network Interconnection ....6
3.1. DC NVO3 Virtual Network Access via the Internet ............7
3.2. DC NVO3 Virtual Network and SP WAN VPN Interconnection .....8
4. DC Applications Using NVO3 ......................................9
4.1. Supporting Multiple Technologies ...........................9
4.2. DC Applications Spanning Multiple Physical Zones ..........10
4.3. Virtual Data Center (vDC) .................................10
5. Summary ........................................................12
6. Security Considerations ........................................12
7. IANA Considerations ............................................12
8. Informative References .........................................13
Acknowledgements...................................................14
Contributors ......................................................15
Authors' Addresses.................................................16
Yong, et al. Informational PAGE 2
RFC 8151 NVO3 Use Case May 2017
1. Introduction
Server virtualization has changed the Information Technology (IT)
industry in terms of the efficiency, cost, and speed of providing new
applications and/or services such as cloud applications. However,
traditional data center (DC) networks have limits in supporting cloud
applications and multi-tenant networks [RFC 7364]. The goal of data
center Network Virtualization over Layer 3 (NVO3) networks is to
decouple the communication among tenant systems from DC physical
infrastructure networks and to allow one physical network
infrastructure to:
o carry many NVO3 virtual networks and isolate the traffic of
different NVO3 virtual networks on a physical network.
o provide independent address space in individual NVO3 virtual
network such as Media Access Control (MAC) and IP.
o Support flexible Virtual Machines (VMs) and/or workload placement
including the ability to move them from one server to another
without requiring VM address changes and physical infrastructure
network configuration changes, and the ability to perform a "hot
move" with no disruption to the live application running on those
VMs.
These characteristics of NVO3 virtual networks (VNs) help address the
issues that cloud applications face in data centers [RFC 7364].
Hosts in one NVO3 VN may communicate with hosts in another NVO3 VN
that is carried by the same physical network, or different physical
network, via a gateway. The use-case examples for the latter are as
follows:
1) DCs that migrate toward an NVO3 solution will be done in steps,
where a portion of tenant systems in a VN are on virtualized
servers while others exist on a LAN.
2) many DC applications serve Internet users who are on different
physical networks;
3) some applications are CPU bound, such as Big Data analytics, and
may not run on virtualized resources.
The inter-VN policies are usually enforced by the gateway.
This document describes general NVO3 VN use cases that apply to
various data centers. The use cases described here represent the DC
provider's interests and vision for their cloud services. The
Yong, et al. Informational PAGE 3
RFC 8151 NVO3 Use Case May 2017
document groups the use cases into three categories from simple to
sophisticated in terms of implementation. However, the
implementation details of these use cases are outside the scope of
this document. These three categories are described below:
o Basic NVO3 VNs (Section 2). All Tenant Systems (TSs) in the
network are located within the same DC. The individual networks
can be either Layer 2 (L2) or Layer 3 (L3). The number of NVO3
VNs in a DC is much larger than the number that traditional VLAN-
based virtual networks [IEEE802.1Q] can support.
o A virtual network that spans across multiple DCs and/or to
customer premises where NVO3 virtual networks are constructed and
interconnect other virtual or physical networks outside the DC.
An enterprise customer may use a traditional carrier-grade VPN or
an IPsec tunnel over the Internet to communicate with its systems
in the DC. This is described in Section 3.
o DC applications or services require an advanced network that
contains several NVO3 virtual networks that are interconnected by
gateways. Three scenarios are described in Section 4:
(1) supporting multiple technologies;
(2) constructing several virtual networks as a tenant network; and
(3) applying NVO3 to a virtual Data Center (vDC).
The document uses the architecture reference model defined in
[RFC 7365] to describe the use cases.
1.1. Terminology
This document uses the terminology defined in [RFC 7365] and
[RFC 4364]. Some additional terms used in the document are listed
here.
ASBR: Autonomous System Border Router.
DC: Data Center.
DMZ: Demilitarized Zone. A computer or small subnetwork
between a more-trusted internal network, such as a
corporate private LAN, and an untrusted or less-trusted
external network, such as the public Internet.
DNS: Domain Name Service [RFC 1035].
Yong, et al. Informational PAGE 4
RFC 8151 NVO3 Use Case May 2017
DC Operator: An entity that is responsible for constructing and
managing all resources in DCs, including, but not
limited to, computing, storage, networking, etc.
DC Provider: An entity that uses its DC infrastructure to offer
services to its customers.
NAT: Network Address Translation [RFC 3022].
vGW: virtual GateWay. A gateway component used for an NVO3
virtual network to interconnect with another
virtual/physical network.
NVO3: Network Virtualization over Layer 3. A virtual network
that is implemented based on the NVO3 architecture.
PE: Provider Edge.
SP: Service Provider.
TS: A Tenant System, which can be instantiated on a physical
server or virtual machine (VM).
VRF-LITE: Virtual Routing and Forwarding - LITE [VRF-LITE].
VN: Virtual Network
VoIP: Voice over IP
WAN VPN: Wide Area Network Virtual Private Network [RFC 4364]
[RFC 7432].
1.2. NVO3 Background
An NVO3 virtual network is in a DC that is implemented based on the
NVO3 architecture [RFC 8014]. This architecture is often referred to
as an overlay architecture. The traffic carried by an NVO3 virtual
network is encapsulated at a Network Virtualization Edge (NVE)
[RFC 8014] and carried by a tunnel to another NVE where the traffic is
decapsulated and sent to a destination Tenant System (TS). The NVO3
architecture decouples NVO3 virtual networks from the DC physical
network configuration. The architecture uses common tunnels to carry
NVO3 traffic that belongs to multiple NVO3 virtual networks.
An NVO3 virtual network may be an L2 or L3 domain. The network
provides switching (L2) or routing (L3) capability to support host
(i.e., TS) communications. An NVO3 virtual network may be required
to carry unicast traffic and/or multicast or broadcast/unknown-
Yong, et al. Informational PAGE 5
RFC 8151 NVO3 Use Case May 2017
unicast (for L2 only) traffic to/from TSs. There are several ways to
transport NVO3 virtual network Broadcast, Unknown Unicast, and
Multicast (BUM) traffic [NVO3MCAST].
An NVO3 virtual network provides communications among TSs in a DC. A
TS can be a physical server/device or a VM on a server end-device
[RFC 7365].
2. DC with a Large Number of Virtual Networks
A DC provider often uses NVO3 virtual networks for internal
applications where each application runs on many VMs or physical
servers and the provider requires applications to be segregated from
each other. A DC may run a larger number of NVO3 virtual networks to
support many applications concurrently, where a traditional VLAN
solution based on IEEE 802.1Q is limited to 4094 VLANs.
Applications running on VMs may require a different quantity of
computing resources, which may result in a computing-resource
shortage on some servers and other servers being nearly idle. A
shortage of computing resources may impact application performance.
DC operators desire VM or workload movement for resource-usage
optimization. VM dynamic placement and mobility results in frequent
changes of the binding between a TS and an NVE. The TS reachability
update mechanisms should take significantly less time than the
typical retransmission Timeout window of a reliable transport
protocol such as TCP and Stream Control Transmission Protocol (SCTP),
so that endpoints' transport connections won't be impacted by a TS
becoming bound to a different NVE. The capability of supporting many
TSs in a virtual network and many virtual networks in a DC is
critical for an NVO3 solution.
When NVO3 virtual networks segregate VMs belonging to different
applications, DC operators can independently assign MAC and/or IP
address space to each virtual network. This addressing is more
flexible than requiring all hosts in all NVO3 virtual networks to
share one address space. In contrast, typical use of IEEE 802.1Q
VLANs requires a single common MAC address space.
3. DC NVO3 Virtual Network and External Network Interconnection
Many customers (enterprises or individuals) who utilize a DC
provider's compute and storage resources to run their applications
need to access their systems hosted in a DC through Internet or
Service Providers' Wide Area Networks (WAN). A DC provider can
construct a NVO3 virtual network that provides connectivity to all
the resources designated for a customer, and it allows the customer
Yong, et al. Informational PAGE 6
RFC 8151 NVO3 Use Case May 2017
to access the resources via a virtual GateWay (vGW). WAN
connectivity to the vGW can be provided by VPN technologies such as
IPsec VPNs [RFC 4301] and BGP/MPLS IP VPNs [RFC 4364].
If a virtual network spans multiple DC sites, one design using NVO3
is to allow the network to seamlessly span the sites without DC
gateway routers' termination. In this case, the tunnel between a
pair of NVEs can be carried within other intermediate tunnels over
the Internet or other WANs, or an intra-DC tunnel and inter-DC
tunnel(s) can be stitched together to form an end-to-end tunnel
between the pair of NVEs that are in different DC sites. Both cases
will form one NVO3 virtual network across multiple DC sites.
Two use cases are described in the following sections.
3.1. DC NVO3 Virtual Network Access via the Internet
A customer can connect to an NVO3 virtual network via the Internet in
a secure way. Figure 1 illustrates an example of this case. The
NVO3 virtual network has an instance at NVE1 and NVE2, and the two
NVEs are connected via an IP tunnel in the DC. A set of TSs are
attached to NVE1 on a server. NVE2 resides on a DC Gateway device.
NVE2 terminates the tunnel and uses the VN Identifier (VNID) on the
packet to pass the packet to the corresponding vGW entity on the DC
GW (the vGW is the default gateway for the virtual network). A
customer can access their systems, i.e., TS1 or TSn, in the DC via
the Internet by using an IPsec tunnel [RFC 4301]. The IPsec tunnel is
configured between the vGW and the customer gateway at the customer
site. Either a static route or Internal Border Gateway Protocol
(IBGP) may be used for prefix advertisement. The vGW provides IPsec
functionality such as authentication scheme and encryption; IBGP
traffic is carried within the IPsec tunnel. Some vGW features are
listed below:
o The vGW maintains the TS/NVE mappings and advertises the TS prefix
to the customer via static route or IBGP.
o Some vGW functions such as the firewall and load-balancer (LB) can
be performed by locally attached network appliance devices.
o If the NVO3 virtual network uses different address space than
external users, then the vGW needs to provide the NAT function.
o More than one IPsec tunnel can be configured for redundancy.
Yong, et al. Informational PAGE 7
RFC 8151 NVO3 Use Case May 2017
o The vGW can be implemented on a server or VM. In this case, IP
tunnels or IPsec tunnels can be used over the DC infrastructure.
o DC operators need to construct a vGW for each customer.
Server+---------------+
| TS1 TSn |
| |...| |
| +-+---+-+ | Customer Site
| | NVE1 | | +-----+
| +---+---+ | | GW |
+------+--------+ +--+--+
| *
L3 Tunnel *
| *
DC GW +------+---------+ .--. .--.
| +---+---+ | ( '* '.--.
| | NVE2 | | .-.' * )
| +---+---+ | ( * Internet )
| +---+---+. | ( * /
| | vGW | * * * * * * * * '-' '-'
| +-------+ | | IPsec \../ \.--/'
| +--------+ | Tunnel
+----------------+
DC Provider Site
Figure 1: DC Virtual Network Access via the Internet
3.2. DC NVO3 Virtual Network and SP WAN VPN Interconnection
In this case, an enterprise customer wants to use a Service Provider
(SP) WAN VPN [RFC 4364] [RFC 7432] to interconnect its sites with an
NVO3 virtual network in a DC site. The SP constructs a VPN for the
enterprise customer. Each enterprise site peers with an SP PE. The
DC provider and VPN SP can build an NVO3 virtual network and a WAN
VPN independently, and then interconnect them via a local link or a
tunnel between the DC GW and WAN PE devices. The control plane
interconnection options between the DC and WAN are described in
[RFC 4364]. Using the option "a" specified in [RFC 4364] with VRF-LITE
[VRF-LITE], both ASBRs, i.e., DC GW and SP PE, maintain a
routing/forwarding table (VRF). Using the option "b" specified in
[RFC 4364], the DC ASBR and SP ASBR do not maintain the VRF table;
they only maintain the NVO3 virtual network and VPN identifier
mappings, i.e., label mapping, and swap the label on the packets in
the forwarding process. Both option "a" and option "b" allow the se
of NVO3 VNs and VPNs using their own identifiers, and two identifiers
are mapped at the DC GW. With the option "c" in [RFC 4364], the VN
Yong, et al. Informational PAGE 8
RFC 8151 NVO3 Use Case May 2017
and VPN use the same identifier and both ASBRs perform the tunnel
stitching, i.e., tunnel segment mapping. Each option has pros and
cons [RFC 4364] and has been deployed in SP networks depending on the
application requirements. BGP is used in these options for route
distribution between DCs and SP WANs. Note that if the DC is the
SP's DC, the DC GW and SP PE can be merged into one device that
performs the interworking of the VN and VPN within an Autonomous
System.
These solutions allow the enterprise networks to communicate with the
tenant systems attached to the NVO3 virtual network in the DC without
interfering with the DC provider's underlying physical networks and
other NVO3 virtual networks in the DC. The enterprise can use its
own address space in the NVO3 virtual network. The DC provider can
manage which VM and storage elements attach to the NVO3 virtual
network. The enterprise customer manages which applications run on
the VMs without knowing the location of the VMs in the DC. (See
Section 4 for more information.)
Furthermore, in this use case, the DC operator can move the VMs
assigned to the enterprise from one sever to another in the DC
without the enterprise customer being aware, i.e., with no impact on
the enterprise's "live" applications. Such advanced technologies
bring DC providers great benefits in offering cloud services, but add
some requirements for NVO3 [RFC 7364] as well.
4. DC Applications Using NVO3
NVO3 technology provides DC operators with the flexibility in
designing and deploying different applications in an end-to-end
virtualization overlay environment. The operators no longer need to
worry about the constraints of the DC physical network configuration
when creating VMs and configuring a network to connect them. A DC
provider may use NVO3 in various ways, in conjunction with other
physical networks and/or virtual networks in the DC. This section
highlights some use cases for this goal.
4.1. Supporting Multiple Technologies
Servers deployed in a large DC are often installed at different
times, and they may have different capabilities/features. Some
servers may be virtualized, while others may not; some may be
equipped with virtual switches, while others may not. For the
servers equipped with Hypervisor-based virtual switches, some may
support a standardized NVO3 encapsulation, some may not support any
encapsulation, and some may support a documented encapsulation
protocol (e.g., Virtual eXtensible Local Area Network (VXLAN)
[RFC 7348] and Network Virtualization using Generic Routing
Yong, et al. Informational PAGE 9
RFC 8151 NVO3 Use Case May 2017
Encapsulation (NVGRE) [RFC 7637]) or proprietary encapsulations. To
construct a tenant network among these servers and the Top-of-Rack
(ToR) switches, operators can construct one traditional VLAN network
and two virtual networks where one uses VXLAN encapsulation and the
other uses NVGRE, and interconnect these three networks via a gateway
or virtual GW. The GW performs packet encapsulation/decapsulation
translation between the networks.
Another case is that some software of a tenant has high CPU and
memory consumption, which only makes sense to run on standalone
servers; other software of the tenant may be good to run on VMs.
However, provider DC infrastructure is configured to use NVO3 to
connect VMs and VLANs [IEEE802.1Q] to physical servers. The tenant
network requires interworking between NVO3 and traditional VLAN.
4.2. DC Applications Spanning Multiple Physical Zones
A DC can be partitioned into multiple physical zones, with each zone
having different access permissions and running different
applications. For example, a three-tier zone design has a front zone
(Web tier) with Web applications, a mid zone (application tier) where
service applications such as credit payment or ticket booking run,
and a back zone (database tier) with Data. External users are only
able to communicate with the Web application in the front zone; the
back zone can only receive traffic from the application zone. In
this case, communications between the zones must pass through one or
more security functions in a physical DMZ zone. Each zone can be
implemented by one NVO3 virtual network and the security functions in
DMZ zone can be used to between two NVO3 virtual networks, i.e., two
zones. If network functions (NFs), especially the security functions
in the physical DMZ, can't process encapsulated NVO3 traffic, the
NVO3 tunnels have to be terminated for the NF to perform its
processing on the application traffic.
4.3. Virtual Data Center (vDC)
An enterprise DC may deploy routers, switches, and network appliance
devices to construct its internal network, DMZ, and external network
access; it may have many servers and storage running various
applications. With NVO3 technology, a DC provider can construct a
vDC over its physical DC infrastructure and offer a vDC service to
enterprise customers. A vDC at the DC provider site provides the
same capability as the physical DC at a customer site. A customer
manages its own applications running in its vDC. A DC provider can
further offer different network service functions to the customer.
The network service functions may include a firewall, DNS, LB,
gateway, etc.
Yong, et al. Informational PAGE 10
RFC 8151 NVO3 Use Case May 2017
Figure 2 illustrates one such scenario at the service-abstraction
level. In this example, the vDC contains several L2 VNs (L2VNx,
L2VNy, L2VNz) to group the tenant systems together on a per-
application basis, and one L3 VN (L3VNa) for the internal routing. A
network firewall and gateway runs on a VM or server that connects to
L3VNa and is used for inbound and outbound traffic processing. An LB
is used in L2VNx. A VPN is also built between the gateway and
enterprise router. An Enterprise customer runs Web/Mail/Voice
applications on VMs within the vDC. The users at the Enterprise site
access the applications running in the vDC via the VPN; Internet
users access these applications via the gateway/firewall at the DC
provider site.
Internet ^ Internet
|
^ +--+---+
| | GW |
| +--+---+
| |
+-------+--------+ +--+---+
|Firewall/Gateway+--- VPN-----+router|
+-------+--------+ +-+--+-+
| | |
...+.... |..|
+-------: L3 VNa :---------+ LANs
+-+-+ ........ |
|LB | | | Enterprise Site
+-+-+ | |
...+... ...+... ...+...
: L2VNx : : L2VNy : : L2VNz :
....... ....... .......
|..| |..| |..|
| | | | | |
Web App. Mail App. VoIP App.
DC Provider Site
Figure 2: Virtual Data Center Abstraction View
The enterprise customer decides which applications should be
accessible only via the intranet and which should be assessable via
both the intranet and Internet, and it configures the proper security
policy and gateway function at the firewall/gateway. Furthermore, an
enterprise customer may want multi-zones in a vDC (see Section 4.2)
for the security and/or the ability to set different QoS levels for
the different applications.
Yong, et al. Informational PAGE 11
RFC 8151 NVO3 Use Case May 2017
The vDC use case requires an NVO3 solution to provide DC operators
with an easy and quick way to create an NVO3 virtual network and NVEs
for any vDC design, to allocate TSs and assign TSs to the
corresponding NVO3 virtual network and to illustrate vDC topology and
manage/configure individual elements in the vDC in a secure way.
5. Summary
This document describes some general NVO3 use cases in DCs. The
combination of these cases will give operators the flexibility and
capability to design more sophisticated support for various cloud
applications.
DC services may vary, NVO3 virtual networks make it possible to scale
a large number of virtual networks in a DC and ensure the network
infrastructure not impacted by the number of VMs and dynamic workload
changes in a DC.
NVO3 uses tunnel techniques to deliver NVO3 traffic over DC physical
infrastructure network. A tunnel encapsulation protocol is
necessary. An NVO3 tunnel may, in turn, be tunneled over other
intermediate tunnels over the Internet or other WANs.
An NVO3 virtual network in a DC may be accessed by external users in
a secure way. Many existing technologies can help achieve this.
6. Security Considerations
Security is a concern. DC operators need to provide a tenant with a
secured virtual network, which means one tenant's traffic is isolated
from other tenants' traffic and is not leaked to the underlay
networks. Tenants are vulnerable to observation and data
modification/injection by the operator of the underlay and should
only use operators they trust. DC operators also need to prevent a
tenant application attacking their underlay DC networks; further,
they need to protect a tenant application attacking another tenant
application via the DC infrastructure network. For example, a tenant
application attempts to generate a large volume of traffic to
overload the DC's underlying network. This can be done by limiting
the bandwidth of such communications.
7. IANA Considerations
This document does not require any IANA actions.
Yong, et al. Informational PAGE 12
RFC 8151 NVO3 Use Case May 2017
8. Informative References
[IEEE802.1Q] IEEE, "IEEE Standard for Local and metropolitan area
networks -- Media Access Control (MAC) Bridges and
Virtual Bridged Local Area Networks", IEEE Std
802.1Q-2011, DOI 10.1109/IEEESTD.2011.6009146.
[NVO3MCAST] Ghanwani, A., Dunbar, L., McBride, M., Bannai, V., and
R. Krishnan, "A Framework for Multicast in Network
Virtualization Overlays", Work in Progress,
draft-ietf-nvo3-mcast-framework-07, May 2016.
[RFC 1035] Mockapetris, P., "Domain names - implementation and
specification", STD 13, RFC 1035,
DOI 10.17487/RFC 1035, November 1987,
<http://www.rfc-editor.org/info/RFC 1035>.
[RFC 3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022,
DOI 10.17487/RFC 3022, January 2001,
<http://www.rfc-editor.org/info/RFC 3022>.
[RFC 4301] Kent, S. and K. Seo, "Security Architecture for the
Internet Protocol", RFC 4301, DOI 10.17487/RFC 4301,
December 2005,
<http://www.rfc-editor.org/info/RFC 4301>.
[RFC 4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", RFC 4364, DOI 10.17487/RFC 4364,
February 2006,
<http://www.rfc-editor.org/info/RFC 4364>.
[RFC 7348] Mahalingam, M., Dutt, D., Duda, K., Agarwal, P.,
Kreeger, L., Sridhar, T., Bursell, M., and C. Wright,
"Virtual eXtensible Local Area Network (VXLAN): A
Framework for Overlaying Virtualized Layer 2 Networks
over Layer 3 Networks", RFC 7348,
DOI 10.17487/RFC 7348, August 2014,
<http://www.rfc-editor.org/info/RFC 7348>.
[RFC 7364] Narten, T., Ed., Gray, E., Ed., Black, D., Fang, L.,
Kreeger, L., and M. Napierala, "Problem Statement:
Overlays for Network Virtualization", RFC 7364,
DOI 10.17487/RFC 7364, October 2014,
<http://www.rfc-editor.org/info/RFC 7364>.
Yong, et al. Informational PAGE 13
RFC 8151 NVO3 Use Case May 2017
[RFC 7365] Lasserre, M., Balus, F., Morin, T., Bitar, N., and Y.
Rekhter, "Framework for Data Center (DC) Network
Virtualization", RFC 7365, DOI 10.17487/RFC 7365,
October 2014,
<http://www.rfc-editor.org/info/RFC 7365>.
[RFC 7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A.,
Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-
Based Ethernet VPN", RFC 7432, DOI 10.17487/RFC 7432,
February 2015,
<http://www.rfc-editor.org/info/RFC 7432>.
[RFC 7637] Garg, P., Ed., and Y. Wang, Ed., "NVGRE: Network
Virtualization Using Generic Routing Encapsulation",
RFC 7637, DOI 10.17487/RFC 7637, September 2015,
<http://www.rfc-editor.org/info/RFC 7637>.
[RFC 8014] Black, D., Hudson, J., Kreeger, L., Lasserre, M., and
T. Narten, "An Architecture for Data-Center Network
Virtualization over Layer 3 (NVO3)", RFC 8014,
DOI 10.17487/RFC 8014, December 2016,
<http://www.rfc-editor.org/info/RFC 8014>.
[VRF-LITE] Cisco, "Configuring VRF-lite",
<http://www.cisco.com/c/en/us/td/docs/switches/lan/
catalyst4500/12-2/31sg/configuration/guide/conf/
vrf.pdf>.
Acknowledgements
The authors would like to thank Sue Hares, Young Lee, David Black,
Pedro Marques, Mike McBride, David McDysan, Randy Bush, Uma Chunduri,
Eric Gray, David Allan, Joe Touch, Olufemi Komolafe, Matthew Bocci,
and Alia Atlas for the reviews, comments, and suggestions.
Yong, et al. Informational PAGE 14
RFC 8151 NVO3 Use Case May 2017
Contributors
David Black
Dell EMC
176 South Street
Hopkinton, MA 01748
United States of America
Email: David.Black@dell.com
Vinay Bannai
PayPal
2211 N. First Street
San Jose, CA 95131
United States of America
Phone: +1-408-967-7784
Email: vbannai@paypal.com
Ram Krishnan
Brocade Communications
San Jose, CA 95134
United States of America
Phone: +1-408-406-7890
Email: ramk@brocade.com
Kieran Milne
Juniper Networks
1133 Innovation Way
Sunnyvale, CA 94089
United States of America
Phone: +1-408-745-2000
Email: kmilne@juniper.net
Yong, et al. Informational PAGE 15
RFC 8151 NVO3 Use Case May 2017
Authors' Addresses
Lucy Yong
Huawei Technologies
Phone: +1-918-808-1918
Email: lucy.yong@huawei.com
Linda Dunbar
Huawei Technologies,
5340 Legacy Drive
Plano, TX 75025
United States of America
Phone: +1-469-277-5840
Email: linda.dunbar@huawei.com
Mehmet Toy
Verizon
Email: mehmet.toy@verizon.com
Aldrin Isaac
Juniper Networks
1133 Innovation Way
Sunnyvale, CA 94089
United States of America
Email: aldrin.isaac@gmail.com
Vishwas Manral
Nano Sec Co
3350 Thomas Rd.
Santa Clara, CA
United States of America
Email: vishwas@nanosec.io
Yong, et al. Informational PAGE 16
RFC TOTAL SIZE: 34962 bytes
PUBLICATION DATE: Friday, May 26th, 2017
LEGAL RIGHTS: The IETF Trust (see BCP 78)
|
